Maintenance Tips for Keeping Your Water Heater Working Well


Last Updated on December 10, 2022 by

As with any other kind of electrical gear, a water heater requires at least the same amount of care, if not more. This piece will examine some best practices for installing and maintaining water heaters to extend their lifespan despite the normal expansion and contraction resulting from heating and cooling. To keep your water heater operating at its most efficient level, here are some suggestions that you should follow.


Provide Area around Heater:

It is important to remember to provide some space between the device that will heat the water and the walls when the water heater is installed. If the service expert does not have sufficient space to move about when inspecting the water heater’s components, they will not be able to provide adequate maintenance or repair for the device. If you want the water heater installation done correctly, you should choose experienced professionals. If you ever need to have it fixed or serviced, it should not be difficult to go to those options.


Elevate the Water Heater:

According to the recommendations of various authorities, the heater needs to be set up at a height of at least 1.8 meters (or 6 feet) above the ground. You will get a powerful flow of hot water coming out of your faucet.

Wiring and Switches:

Ensure that the heater is wired to a Miniature Circuit Breaker (MCB), which will turn off the electrical supply if there are variations in the power supply. Because of this, there will be a much-reduced risk of a short circuit occurring in the water heater. Also, the switch should be placed at a high enough height to keep younger children away from it but not so high that it is difficult for adults, including yourself, to reach it. Now that we know what safety measures to take while water heater replacement, let’s look at some maintenance advice that may assist us in keeping the appliance in working order.

Don’t Run the Heater for Too Long:

It is common for people to leave the heater running for lengthy periods, mainly while using it throughout the morning. Because everyone needs warm water in the morning before they hurry to work or school, the conventional wisdom is that leaving the heater running would save time. The case once upon a time, but today’s heaters may heat water in as little as five minutes. Instead of turning on the heaters half an hour in advance, it is more prudent to do so just five minutes before you will require it. Experts from service providers are also available for water heater replacement.

Save Energy by Reducing the Thermostat:

Keeping your water heater in top shape is essential to save money on your utility bill. If you adjust the temperature to lower it, the water will quickly reach the desired temperature. Because of the decrease in temperature, the heater will have to work less, which will allow it to function for a more extended period. Families with young children must reduce the temperature on the thermostat. Maintaining your water heater repair is thus of the utmost importance during the colder months to guarantee that you never run out of hot water.

Inspect the Anode Rod inside the Tank before Winter:

An anti-corrosion anode rod is often housed inside the tank of more enormous heaters. Because this rod draws rust and any other contaminants present in the water, it will stop the tank from rusting or corroding in the future. It is recommended that you inspect the anode rod at least once every three years to determine whether or not the outer coating of magnesium has eroded away and whether or not 6 inches or more of the inner steel core can be seen. If this is the case, the rod in question will need to be replaced.


Make that the Pressure Release Valve is Working Correctly:

The temperature and pressure release valves should be checked at least once a year. Let the pressure out a couple of times fast to prevent this. If the water heater’s pressure release valve leaks, it’s a big deal. The water heaters merely have to have some water drained out of them, and then the output line needs to be removed. After that, you should replace the valve, and you’re finished!


Keep a Close Check on the Connector:

Because of changes in the power supply and because you are utilizing cabling with a limited capacity for the power socket, your switch will ignite every while. The greater electrical wattage will cause the plug and the pins to heat up, leaving burn marks on the plug and the nails. In addition, you will notice burn marks on the plug’s pins. It is always best to use plugs and sockets that are new and that have been correctly connected and plugged in so that any potential future electrical short circuits caused by this may be avoided. The final thing you may do is only turn on the heater when you need it and then turn it off as soon as you’re through using it.


Metalize the Plastics Inlet and Exit Pipes:

It is usually recommended to use metal inlet and outlet pipes rather than the conventional plastic ones with a heater since metal pipes are more resistant to heat than plastic ones. In addition to that, don’t forget to inspect the joints frequently. If you see white deposits around the joints caused by hard water or corrosion, it is time to repair the pipe that supplies the inlet or exit of the water heater.

Get Yearly Maintenance Done:

Finally, if you don’t know what you’re doing for heater maintenance and want to prevent water heater issues, it’s best to hire a specialist to handle the job instead of attempting to do it yourself. To prevent water heater issues, this is extremely important. Additionally, they will assist you in cleaning out your water heater.


It is highly recommended that you do routine maintenance on your water heater replacement to keep it in excellent working order. These machines are essential to our daily existence, and in their absence, we would struggle to function correctly. You should never ignore your water heater or leave its maintenance up to chance, no matter what sort of water heater you have.